Verwenden Sie den Reader unten, um das Flymo EasiLife Go 200 Roboterrasenmäher Bedienungsanleitung zu lesen. Sie können die Anleitungen direkt auf der Seite durchblättern und die Funktionen unseres Readers nutzen, um alle wichtigen Informationen zur Installation, Bedienung und Wartung dieser Flymo Roboterrasenmäher zu finden.
Bedienungsanleitung
VollbildFehlerbehebung
Praktische Tipps zur Lösung der häufigsten Probleme mit Flymo EasiLife Go 200.
Ursache: Grass or other object around the drive wheel
Remove grass or other object
Ursache: Grass or other object around the blade disc or blade disc in water
Remove grass or other object. Move the product and prevent the collection of water in the work area
Ursache: Grass exceeds maximum height of 4 cm / 1.6 in
Cut the grass before you install the product. Make sure that the grass is maximum 4 cm / 1.6 in
Ursache: Product is behind a number of obstacles in a small area
Remove the obstacles or put the boundary wire around the obstacle to make an island
Ursache: Boundary wire section is put across another section, too near the edge, slopes much, put in incorrect direction, or interference from metal objects
Make sure that the boundary wire is connected and installed correctly. Move the boundary wire if necessary
Ursache: Product cannot find the charging station, battery is at the end of its life cycle, antenna is defective, or charging plates are corroded
Change the position of the guide wire. Replace the battery if needed. Clean the charging plates and contact plates. Check the indicator lamp in the charging station
Ursache: Incorrect PIN code has been entered
Enter the correct PIN code. Contact Flymo service if you do not know the correct PIN code
Ursache: Product has got caught in something and has been slipping or work area includes a steep slope
Free the product and correct the cause of problem. If it is because of wet grass, wait until the lawn is dry before you use the product
Ursache: Grass or other object around the drive wheel
Remove grass or object from the drive wheel
Ursache: Front wheels on the product are blocked
Free the product and correct the cause of problem. Contact Flymo service if the problem stays
Ursache: Contact between charging plates is not good, object prevents the product to enter the charging station, charging station is tilted or bent, or guide wire is not installed correctly
Put the product in the charging station and make sure that the charging plates and contact plates are connected. Remove the object. Put the baseplate on level ground. Install the guide wire correctly
Ursache: Object prevents the product to move out from the charging station
Remove the object
Ursache: Product is in an incorrect position, tilting too much or is upside down
Put the product in the correct position
Ursache: Lift sensor has been enabled because the product has been lifted
Make sure that the product body can move freely around its chassis. Remove or create an island around objects that can cause the chassis to be lifted
Ursache: Grass or other object around the drive wheel
Clean the wheels and around the wheels
Ursache: Temporary electronic or firmware related problem in the product
Restart the product. Contact Flymo service if the problem stays
Ursache: Incorrect type of battery
Use original batteries recommended by the manufacturer
Ursache: Temporary battery or firmware related problem in the product or incorrect type of battery
Restart the product. Use original batteries recommended by the manufacturer. Contact Flymo service if the problem stays
Ursache: The temperature in the battery is too high or too low to start operation
Wait until the temperature is restored to its limits. Charging/mowing will start when the temperature is in its operating limits
Ursache: Incorrect or defective power supply unit
Restart the product. Replace the power supply if needed. Contact Flymo service if the problem stays
Ursache: Power supply or low-voltage cable are not connected or damaged, boundary wire is not connected or damaged, product is not in charging station with ECO mode enabled, boundary wire is installed incorrectly, or interference from metal objects
Check the power outlet connection and residual-current device. Make sure that the low-voltage cable is connected to the charging station. Replace the power supply or low-voltage cable if damaged. Connect the boundary wire to the charging station. Replace the connectors if damaged. Put the product in the charging station and make a new loop signal
Ursache: Product is tilted more than the maximum angle
Move the product to a level area
Ursache: Product cannot find the charging station, battery is at the end of its life cycle, antenna is defective, or charging plates are corroded
Change the position of the guide wire. Replace the battery if needed. Clean the charging and contact plates. Contact approved servicing dealer if the problem stays
Ursache: Guide wire is not connected to the charging station, guide wire is damaged, or guide wire is not connected to the boundary loop
Connect the guide wire to the charging station and to the boundary loop correctly. Replace the damaged section with new guide wire
Häufig gestellte Fragen
Die häufigsten Fragen zum Flymo EasiLife Go 200.
Hilfe
Hast du Fragen zur Roboterrasenmäher EasiLife Go 200 von Flymo? Stelle sie direkt unserem Experten! Du erhältst Informationen, praktische Tipps und maßgeschneiderte Lösungen in nur wenigen Sekunden.
Ähnliche Bedienungsanleitungen
Unten finden Sie Bedienungsanleitungen für Roboterrasenmäher, die ähnlich wie EasiLife Go 200 sind. Versuchen Sie auch, alle Flymo Roboterrasenmäher Bedienungsanleitungen anzusehen
Diskussion
Hinterlassen Sie einen Kommentar oder stellen Sie eine Frage
An der Diskussion teilnehmen
Stellen Sie eine Frage zum Handbuch oder fügen Sie eine hilfreiche Antwort für andere Nutzer hinzu.