1 General
5
1.1 Explanations Of The Symbols
5
1.2 Information Regarding The Manual
5
1.3 Liability And Warranty
6
1.4 Copyright
6
1.6 Spare Parts
6
1.7 Disposal
7
2 Safety
8
2.1 Intended Use
8
2.2 Manual Contents
8
2.3 Making Changes And Modifications To The Machine
8
2.4 Responsibilities Of The Operator
9
2.5 What Is Required Of The Personnel
9
2.6 Work Safety
9
2.7 Personal Safety
10
2.8 Hazards Arising From The Machine
10
2.9 Other Risks
10
3 Declaration Of Conformity
11
4 Technical Data
12
4.1 Dimensions And Weight
12
4.2 Operation And Storage Conditions
12
4.3 Electrical Connection
12
4.4 Noise Emissions
13
4.5 Dust Extraction
14
5. Setting Up The Machine
15
5.1 Overview
15
5.2 Data Plate
16
6 Setup And Installation
17
6.1 Safety Instructions
17
6.2 Positioning
17
6.2.1 Safety Instructions
18
6.2.2 Setting Up The Work Table
18
7 Operation
19
7.1 Safety Instructions
19
7.2 Switching On The Machine
20
7.3 Authorised Work Techniques
20
7.4 Authorised Work Techniques
21
7.4.1 Positioning The 90° End Stop On The Work Table
21
7.4.2 Parallel Cutting Fence
21
7.4.3 Saw Blade Replacement/Tension
22
7.4.4 Longitudinal Cut Along The Marked Line
22
7.4.5 Cutting Round Work-Pieces In The Transverse Direction
23
7.4.6 Longitudinal Cut Of Narrow Or Thin Work-Pieces With The Guide Fence
23
7.4.7 Cutting Work-Pieces On The Upright Edge
23
7.4.8 Angular Cuts
24
7.4.9 Circular Cuts
24
7.4.10 Diagonal Cross Cuts Of Rectangular Work-Pieces
24
7.5 Applications
25
7.5.1 Blade Selection And Maintenance
25
7.5.2 Adjusting The Saw Blade Guide
26
7.5.2.1 Upper Blade Guide
26
7.5.2.2 Lower Blade Guide
26
8. Maintenance
27
8.1 Safety Instructions
27
8.2 Cleaning And Lubrication
27
8.3 Drive Belts
28
8.3.1 Adjusting The Belt Tension
28
9 Faults
29
9.1 Safety Instructions
29
9.2 What To Do In Case Of A Fault
29
9.3 What To Do After Rectifying The Fault
29
9.4 Faults, Causes And Repairs
30
10 Circuit Diagram
32
10.1 Safety Instructions
32
11 Spare Parts
34
11.1 Machine Base-Frame
34
11.2 Machine Table
35
11.3 Height Adjustable Protection Device
36
11.4 Upper Wheel
37
11.5 Lower Wheel
38
11.6 Safety Equipment
39
12 Index
40
Diskussion
Hinterlassen Sie einen Kommentar oder stellen Sie eine Frage
Hallo, ich habe seit kurzem die Hammer N4400 und bin mir nicht sicher wie ich das Sägeblatt richtig wechsle. Habe Angst dass ich was falsch mache und der Schnitt dann nicht mehr gerade ist. Gibt es da einen Trick oder eine bestimmte Reihenfolge die ich beachten muss?
Den Sägeblattwechsel bei der N4400 habe ich auch am Anfang nicht auf Anhieb hinbekommen. Wichtig ist, dass du nach dem Wechsel unbedingt die Parallelität des Blattes zum Führungsschlitz neu überprüfst und gegebenenfalls nachstellst. Die Spannvorrichtung muss gleichmäßig angezogen werden, sonst läuft das Blatt schief. Schau dir auf jeden Fall die entsprechenden Abschnitte im Handbuch genau an, da sind die Einstellwerte für die N4400 konkret angegeben. Damit sparst du dir viel Frust.
An der Diskussion teilnehmen
Stellen Sie eine Frage zum Handbuch oder fügen Sie eine hilfreiche Antwort für andere Nutzer hinzu.