Gardena Smart Sileno Free 1500 Roboterrasenmäher Bedienungsanleitung

Ursache: Mowing area slopes too much by the virtual boundary or interference from metal objects near charging station

Ensure mowing area is installed correctly, change position of charging station

Ursache: Product cannot find charging station, poor satellite coverage, obstacle blocking charging station, battery end of life, or damaged charging station antenna

Examine satellite coverage, remove obstacles, replace battery if needed, contact authorized service if antenna is damaged

Ursache: Product caught in something and slipping, or steep slope in installation

Free the product and correct cause, isolate steep slopes, wait until lawn is dry

Ursache: Grass or other object around the drive wheel

Remove grass or object from the drive wheel

Ursache: Front wheels on the product are blocked

Free the product and correct cause, contact GARDENA service if problem persists

Ursache: Poor contact between charging plates, object blocking entry, or charging station is tilted/bent

Ensure charging plates and contact plates are connected, remove object, put baseplate on level ground

Ursache: Object prevents product movement out from charging station

Remove the object

Ursache: Product in incorrect position, tilting too much, or upside down

Put the product in the correct position

Ursache: Lift sensor enabled because product has been lifted

Ensure product body moves freely around chassis, remove or create island around objects causing chassis lift, contact GARDENA service if persists

Ursache: Grass or other object around the drive wheel

Clean the wheels and around the wheels

Ursache: Temporary electronic or firmware related problem

Restart the product, contact GARDENA service if problem persists

Ursache: Corrosion or dirt on charging plates and contact plates, or temporary electronic/firmware problem

Restart the product, clean charging plates on product and contact plates on charging station, contact authorized service if problem persists

Ursache: Temporary battery or firmware problem, or incorrect battery type

Restart the product, use original batteries recommended by manufacturer, contact GARDENA service if problem persists

Ursache: Temperature in battery too high or too low to start operation

Charging/mowing will start when temperature is restored to operating limits

Ursache: Incorrect or damaged power supply unit

Restart the product, contact GARDENA service if problem persists

Ursache: Power supply or low-voltage cable not connected, damaged, or interference from metal objects near charging station, or problem with pairing

Check power outlet and residual-current device, ensure low-voltage cable is connected, replace power supply or cable if damaged, redo charging station installation, change charging station position

Ursache: Product tilted more than maximum angle

Move the product to a level area

Ursache: Product stopped because slope is too steep

Change installation to exclude the steep part

Ursache: Vibrations detected in blade disc due to damaged or worn blades, or incorrect blade installation

Examine blades and screws, ensure all blades are correctly installed and only one blade attached in each position

Ursache: Power supply unit incorrect or damaged, power failure, or no contact between charging plates

Examine and replace power supply unit if necessary, find and correct cause of power failure, ensure charging plates are in contact and clean them

Ursache: Way back to charging station blocked by obstacle or No-go zone blocking way to mowing area

Remove the obstacle, edit or remove No-go zone or make new installation of mowing area

Ursache: Way to destination blocked by obstacle or No-go zone

Remove obstacle, edit or remove No-go zone or make new installation of mowing area

Ursache: Battery state of health is low

Replace the battery, speak to authorized service technician

Ursache: Battery state of health is critically low

Replace the battery, speak to authorized service technician

Ursache: Firmware in the product is invalid

Put product in charging station and update firmware via FOTA, speak to authorized service technician if problem remains

Ursache: Edge cutting system blocked by grass or other objects

Examine edge cutting system and remove grass or other objects

Ursache: Vibrations detected in edge blade disc due to damaged or worn blades, or incorrect blade installation

Examine blades and screws, ensure all blades are correctly installed and only one blade attached in each position

Ursache: Weak satellite signal to product

Wait for good satellite signals, examine for objects causing interference between product and sky, remove object or do new installation

Ursache: Map object file is incorrect

Do a check of map in the app, adjust and save map, or delete map and do new installation

Ursache: Charging station was moved

Do a new installation of charging station in the app

Ursache: Product not connected to smart Gateway

Ensure smart Gateway is installed correctly, set to ON and connected to Wi-Fi, change Gateway position to improve connection signal if problem occurs frequently

Ursache: Product stays at docking point until receiving satellite signals for accurate position

Usual operation for the product

Ursache: Charging station not on level surface

Put charging station on level surface

Ursache: Incorrect start and stop times for operating

Change the schedule settings

Ursache: Cutting system not in balance due to damaged blades, too many blades in same position, or different thickness blades

Examine blades and screws, replace if necessary, ensure only one blade attached to each screw, check if blades are of different thickness and replace if necessary

Ursache: Product searches for charging station or is moving to starting point

Usual operation for the product